Top 10 typical forklift mishaps ， forklift operation ought to focus on these matters ！.

Do not take too lightly the forklift at the office. If the procedure is bad, there will certainly be serious accidents in minutes, and there are lots of crashes involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost caused casualties.
Instance 3: The size of the forklift freight surpasses the allowable width of the course and holds on the roadside rack, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not put on the safety belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift driver did not put on a safety belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure ought to take note of these matters ：.

Beginning.
1. Before beginning, observe the surroundings, and after confirming that there are no barriers that hinder the safety and security of driving, honk the horn first and after that start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be safe before beginning.
3. When the forklift starts with a lots, the chauffeur should first validate that the tons is secure and trustworthy.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the height between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not lift the fork too expensive when driving. When going into and leaving the job website or while driving, beware that there will certainly be no challenges overhead. When the load is traveling, the fork should not be elevated too high, which will influence the stability of the forklift. .
3. After discharging, the fork should be reduced to the typical driving placement before driving. .
4. When transforming, if there are pedestrians or cars close by, the driving signal needs to be issued initially. High-speed sharp turns are prohibited. High-speed doglegs will trigger the lorry to shed side stability and tip over. .
5. When the forklift is downhill, it is strictly restricted to turn off the fire and slide, and it is forbidden to brake suddenly while driving with loads unless there are special situations.
6. When the forklift is running, it must comply with the traffic rules in the manufacturing facility and have to keep a certain security range from the lorry ahead. .
7. When the forklift is running, the tons has to remain in the most affordable setting that does not impede the driving, and the gantry needs to be correctly tilted back. The tons shall not be increased except when stacking or packing. .
8. The elevation of the load must not block the chauffeur's view. In unique situations, when the item affects the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility area is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for personnel to depend on the fork to hold products and play a balancing role. .
12. If troubles are discovered, they will be repaired and reported in a prompt way, and they will never ever operate with illnesses or hide them.

loading and dumping.
1. When fork-loading things, the distance in between both forks ought to be adjusted as required to make the load of both forks balanced and not skewed, and one side of the product ought to protest the rack. .
2. It is forbidden to collaborate with a solitary fork or make use of a fork top or draw. In special circumstances, safety and security warning signs must be established to remind bordering pedestrians. .
3. In the process of loading and discharging items, the forklift has to be braked with the brake. .
4. The rate of the car need to be sluggish and constant. Beware not to roll the wheels on the dunnage, so as not to extend the rolled objects and injure people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as feasible under the lots, and it ought to be kept in mind that the fork suggestion must not touch other products or things. The load must be stabilized with very little back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted ahead somewhat when the lots is lowered to enable very easy positioning of the load and extraction of the forks. .
6. It is restricted to fork goods at high speed and hit tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so as to avoid the collapse of the goods and harm individuals. .
8. Straining is banned, and it is restricted to make use of forks to raise personnel to engage in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not permitted to use the brake inertia to slip, put, round or roll objects. .
10. It is not enabled to utilize forks to choose, transform pallet dump.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the parking brake deal with to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for special circumstances, such as the chauffeur does not leave the car's line of sight and does not exceed 1 minute).
4. Remove the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance ought to be examined, and fuel, lubricating oil and cooling water should be included.
2. Examine the safety and security efficiency of starting, running and braking.
3. Examine whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the external leak must likewise be checked and the seals need to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to examine before leaving the cars and truck;.
2. When you come across someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow-moving and uniform, and no activating the incline is allowed.
7. Do not drive throughout the gradient. When the slope is greater than 10%, the lorry ought to be driven in reverse when going downhill;.
8. When the forklift employees bring the goods and move on, if they experience huge or heavy items and go to Stand-on Electric Pallet Stacker the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be complied with in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not permitted to bring individuals to deal with the pallet or fork, and it is strictly restricted to stand under the fork after the fork is elevated.
8. Do not drive side to side on inclines
.
Car park is not permitted under the list below problems.
1. Contours, narrow roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same size as the obstacle ought to be within 20 meters Electric Forklift Truck for Warehouse at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844